Kursaal Extreme Raven 24×24 2CM Porcelain Paver – Natural
Elevate outdoor living with the Kursaal Extreme Raven 24×24 2CM Porcelain Paver. Its deep gray Raven tone delivers a sleek, contemporary foundation, while the Natural finish provides dependable underfoot confidence without sacrificing a refined look. Engineered in a robust 20 mm (2CM) thickness, this porcelain paver is designed for real‑world outdoor performance.
With a DCOF of 0.60 and frost resistance, Kursaal Extreme Raven stands up to the elements on patios, pool decks, walkways, and other open‑air spaces. Pressed edges and the large‑format 24×24 size support clean, consistent layouts, and a PEI 4 wear rating pairs with low‑maintenance porcelain construction for long‑lasting use in residential and commercial exterior projects when installed to industry standards. Approximate coverage is 7.75 sq ft per box.
Features
- 24×24 large-format 20 mm (2CM) porcelain paver
- Raven color in a Natural finish
- Pressed edges for a clean, consistent layout
- DCOF 0.60 for confident wet‑area traction
- PEI 4 wear rating for durable performance
- Frost resistant for year‑round outdoor use
- Low maintenance and easy to clean
- Suitable for residential and commercial exterior applications when installed per standards
- Approx. 7.75 sq ft per box coverage
Recommended Applications
- Patios
- Pool Decks
- Walkways
- Garden Paths
- Outdoor Kitchens
- Outdoor Living Areas
- Rooftop Terraces
- Courtyards
Installation Guide – Kursaal Extreme Raven 24×24 2CM Porcelain Paver – Natural
Important Advisory
This guidance applies to the installation of Happy Floors Kursaal Extreme Raven 24×24 2CM Porcelain Pavers. Always follow manufacturer instructions, local building codes, substrate and drainage requirements, and current industry standards (e.g., TCNA/ANSI) before starting any project.
Step 1: Layout & Planning
- Dry‑lay pavers to review shade, size calibration, and layout before installation.
- Plan patterns and cuts to achieve balanced joints and minimize narrow cut pieces along edges.
- Establish reference lines to maintain straight, consistent courses and proper slope for drainage away from structures.
Step 2: Paver Installation
- Install 24×24 porcelain pavers over a properly prepared and compacted sand setting bed, a bonded mortar bed, or an adjustable pedestal system approved for 2CM porcelain.
- Verify adequate slope and drainage per local codes and site conditions.
- Maintain consistent joint spacing using appropriate spacers and methods for porcelain pavers.
- Seat each paver with a rubber mallet to ensure full support without chipping the pressed edges or surface.
- Check alignment, flatness, and joint consistency frequently, and incorporate movement joints per standards and site conditions.
Step 3: Cutting
- Use a wet saw with a premium diamond blade rated for porcelain.
- Support the paver fully during cutting to minimize edge chipping and improve accuracy.
- Measure carefully and mark clearly before every cut; wear appropriate PPE.
- Avoid dry cutting where possible and control dust per safety regulations.
Step 4: Joint Filling
- For sand‑set installations, fill joints with polymeric sand or another jointing material approved for porcelain pavers and exterior use.
- For mortar‑set installations, use an exterior‑grade grout per manufacturer guidance; clean as you go to reduce haze.
- On pedestal systems, follow the pedestal and spacer manufacturer’s recommendations for joint treatment and perimeter restraint.
- Remove excess jointing material from the surface before curing and perform a final clean per product instructions.
Step 5: Cleaning & Maintenance
- Clean routinely with water and a pH‑neutral cleaner using non‑abrasive tools.
- Avoid acidic, bleach‑based, or abrasive products that may harm surrounding materials or finishes.
- Promptly remove construction residues and grout haze following manufacturer recommendations.
- Porcelain pavers generally do not require sealing; inspect joints, borders, and drainage periodically and maintain as needed.
Disclaimer
Shade and size variation can occur between production runs; verify caliber and dye lot before installation. Inspect all materials prior to install—installed materials are considered accepted. Professional installation is recommended to ensure code compliance, structural integrity, and long‑term performance.
