X-Rock White 24×24 2CM Porcelain Paver – Natural
Bring a clean, contemporary look to outdoor spaces with the X-Rock White 24×24 2CM Porcelain Paver. Its light, versatile tone and natural finish create a refined foundation that pairs easily with modern landscape designs, outdoor kitchens, and relaxed entertaining areas.
Engineered at a robust 20 mm (2CM) thickness, this porcelain paver is built for outdoor performance. Rectified edges support tight, consistent joints and straight lines, while the dense porcelain body delivers low‑maintenance durability. With a PEI 4 wear rating and frost resistance for year‑round reliability, it’s a smart choice for patios, terraces, walkways, and other open‑air living areas when installed to industry standards.
Approximate coverage is 7.75 sq ft per box.
Features
- 24×24 large-format 20 mm (2CM) porcelain paver
- White color in a Natural finish
- Rectified edges for precise, consistent joints
- PEI 4 wear rating for durable performance
- Frost resistant for year‑round outdoor use
- Low maintenance and easy to clean
- Approx. 7.75 sq ft per box coverage
- Designed for exterior installations when set per industry standards
Recommended Applications
- Patios
- Walkways
- Garden Paths
- Outdoor Kitchens
- Outdoor Living Areas
- Courtyards
- Rooftop Terraces
Installation Guide – X-Rock White 24×24 2CM Porcelain Paver – Natural
Important Advisory
Always follow the manufacturer’s instructions, local building codes, substrate and drainage requirements, and current industry standards (e.g., TCNA/ANSI) when installing 2CM porcelain pavers.
Step 1: Layout & Planning
- Dry‑lay several pieces to review shade, sizing, and layout before installation.
- Plan patterns and cuts to minimize small slivers at edges and to balance joint lines.
- Establish reference lines with chalk or a laser and confirm proper slope for drainage away from structures.
Step 2: Paver Installation
- Install 24×24 porcelain pavers over a properly prepared and compacted sand setting bed, a bonded mortar bed, or an adjustable pedestal system approved for 2CM porcelain.
- Verify adequate slope and site drainage per code and project requirements.
- Maintain consistent joint spacing (typically about 1/8"–3/16") using appropriate spacers.
- Seat each paver with a rubber mallet to ensure full support without chipping the rectified edges or surface.
- Check alignment, flatness, and joint consistency frequently, and incorporate movement joints per standards and jobsite conditions.
Step 3: Cutting
- Use a wet saw with a premium diamond blade rated for porcelain.
- Support the paver fully during cutting to minimize edge chipping and ensure accuracy.
- Measure carefully and mark clearly; wear appropriate PPE.
- Avoid dry cutting where possible and control dust per safety regulations.
Step 4: Joint Filling
- For sand‑set installations, fill joints with polymeric sand or another jointing material approved for porcelain pavers and exterior use.
- For mortar‑set installations, use an exterior‑grade grout per manufacturer guidance; clean as you go to prevent haze.
- On pedestal systems, follow the pedestal and spacer manufacturer’s recommendations for joint treatment and perimeter restraint.
- Remove excess jointing material before curing and perform a final clean per product instructions.
Step 5: Cleaning & Maintenance
- Clean routinely with water and a pH‑neutral cleaner using non‑abrasive tools.
- Avoid acidic, bleach‑based, or abrasive products that could harm surrounding materials or finishes.
- Promptly remove construction residues and grout haze following manufacturer recommendations.
- Porcelain pavers typically do not require sealing; inspect joints, borders, and drainage periodically and maintain as needed.
Disclaimer
Shade and size variation can occur between production runs; verify caliber and dye lot before installation. Inspect all materials prior to install—installed materials are considered accepted. Professional installation is recommended to ensure code compliance, structural integrity, and long‑term performance.
