Berwyn Multi 24×24 2CM Porcelain Paver – Natural
The Berwyn Multi 24×24 2CM Porcelain Paver introduces a dynamic, multi‑tonal look that complements contemporary and transitional outdoor designs. Its Natural finish offers a refined, understated surface that pairs easily with wood, metal, and lush greenery across patios and terraces.
Engineered in a sturdy 20 mm (2CM) thickness, this porcelain paver is built for exterior performance with low‑maintenance durability. Precisely rectified edges and the large 24×24 format support clean lines and balanced joints. With PEI 4 wear resistance and frost resistance, Berwyn Multi is well suited for year‑round residential outdoor use when installed to industry standards.
Plan your layout with consistent spacing to highlight the paver’s rectified profile, and select an installation method—sand set, mortar bed, or pedestal system—appropriate for site conditions, drainage, and local codes.
Features
- 24×24 large-format 20 mm (2CM) porcelain paver
- Multi color palette in a Natural finish
- Rectified edges for precise, consistent joints
- PEI 4 wear rating for durable performance
- DCOF 0.42 (verify suitability for wet-area requirements)
- Frost resistant for year‑round outdoor use
- Low maintenance and easy to clean
- Approx. 7.75 sq ft per box coverage
- Suitable for residential outdoor applications when installed per standards
Recommended Applications
- Patios
- Walkways
- Garden Paths
- Outdoor Kitchens
- Outdoor Living Areas
- Rooftop Terraces
- Courtyards
- Entryways
Installation Guide – Berwyn Multi 24×24 2CM Porcelain Paver – Natural
Important Advisory
This guidance applies to the installation of Berwyn Multi 24×24 2CM Porcelain Pavers. Always follow manufacturer instructions, local building codes, substrate and drainage requirements, and current industry standards (e.g., TCNA/ANSI) before starting any project.
Step 1: Layout & Planning
- Dry‑lay several pavers to review shade, calibration, and layout prior to installation.
- Plan patterns and cuts to maintain balanced joints and avoid small slivers at edges and borders.
- Establish reference lines with chalk or laser to keep courses straight and preserve the required slope for drainage.
Step 2: Paver Installation
- Install 24×24 porcelain pavers over a properly prepared and compacted sand setting bed, a bonded mortar bed, or an adjustable pedestal system approved for 2CM porcelain.
- Confirm adequate slope and positive drainage away from structures per local codes and site conditions.
- Maintain consistent joint spacing (typically about 1/8″–3/16″) using appropriate spacers.
- Seat each paver with a rubber mallet to ensure full support without chipping the rectified edges or surface.
- Check alignment, flatness, and joint consistency frequently, and incorporate movement joints per standards and project conditions.
Step 3: Cutting
- Cut with a wet saw using a premium diamond blade rated for porcelain.
- Support the paver fully during cutting to minimize edge chipping and improve accuracy.
- Measure carefully and mark clearly before each cut; wear appropriate PPE.
- Avoid dry cutting when possible and control dust per safety regulations.
Step 4: Joint Filling
- For sand‑set installations, fill joints with polymeric sand or another jointing material approved for porcelain pavers and exterior use.
- For mortar‑set installations, use an exterior‑grade grout per manufacturer guidance; clean as you go to reduce haze.
- For pedestal systems, follow pedestal and spacer manufacturer guidance for joint treatment and perimeter restraint.
- Remove all excess jointing material from the surface before curing and final cleaning.
Step 5: Cleaning & Maintenance
- Clean routinely with water and a pH‑neutral cleaner using non‑abrasive tools.
- Avoid acidic, bleach‑based, or abrasive products that may affect surrounding materials or finishes.
- Promptly remove construction residues and grout haze following manufacturer recommendations.
- Porcelain pavers typically do not require sealing; inspect joints, borders, and perimeter restraints periodically and maintain as needed.
Disclaimer
Shade and size variation can occur between production runs; verify caliber and dye lot before installation. Inspect all materials prior to install—installed materials are considered accepted. Professional installation is recommended to ensure code compliance, structural integrity, and long‑term performance.
