Azuma 2.0 NO 24×24 2CM Porcelain Paver – Natural
Bring streamlined, contemporary character to outdoor spaces with the Azuma 2.0 NO 24×24 2CM Porcelain Paver in a natural finish. Precise rectified edges create clean, balanced lines for modern patios, terraces, and walkways while maintaining an understated, refined look.
Engineered for exterior performance in a robust 2CM (approx. 3/4 in.) thickness, this porcelain paver offers low‑maintenance durability and frost resistance for reliable year‑round use. The 24×24 large format supports consistent layouts and an open visual flow when installed to industry standards.
Built from dense porcelain with a PEI 4 wear rating and a DCOF > 0.42, Azuma 2.0 is designed to handle everyday outdoor life with ease. Its practical performance and easy‑care surface make it a smart choice for inviting, long‑lasting outdoor living areas.
Features
- 24×24 large‑format 2CM (approx. 3/4 in.) porcelain paver
- Natural finish for a refined, understated look
- Rectified edges for precise, consistent joints
- PEI 4 wear rating for durable performance
- DCOF > 0.42 (per manufacturer data)
- Frost resistant for dependable year‑round outdoor use
- Low maintenance and easy to clean
- Approx. 7.75 sq ft per box coverage
Recommended Applications
- Patios
- Walkways
- Garden Paths
- Outdoor Kitchens
- Outdoor Living Areas
- Rooftop Terraces
- Courtyards
- Entryways
Installation Guide – Azuma 2.0 NO 24×24 2CM Porcelain Paver – Natural
Important Advisory
This guidance applies to the installation of Azuma 2.0 NO 24×24 2CM Porcelain Pavers in a Natural finish. Always follow manufacturer instructions, local building codes, substrate and drainage requirements, and current industry standards (e.g., TCNA/ANSI) before starting any project.
Step 1: Layout & Planning
- Dry‑lay pavers to review shade, size calibration, and layout prior to install.
- Plan patterns and cuts for balanced joints and to avoid narrow slivers at edges.
- Establish reference lines with chalk or laser to maintain straight courses and correct slope for drainage away from structures.
Step 2: Paver Installation
- Install 24×24 porcelain pavers over a properly prepared and compacted sand setting bed, a bonded mortar bed, or an adjustable pedestal system approved for 2CM porcelain.
- Verify adequate slope and positive drainage per local codes and site conditions.
- Maintain consistent joint spacing (typically about 1/8"–3/16") using appropriate spacers.
- Seat each paver gently with a rubber mallet to ensure full support without chipping the rectified edges or surface.
- Check alignment, flatness, and joint consistency frequently and incorporate movement joints per standards and exposure.
Step 3: Cutting
- Use a wet saw with a premium diamond blade rated for porcelain.
- Support the paver fully during cutting to minimize edge chipping and improve accuracy.
- Measure carefully and mark clearly before each cut; wear appropriate PPE.
- Avoid dry cutting where possible and control dust in accordance with safety regulations.
Step 4: Joint Filling
- For sand‑set installations, fill joints with polymeric sand or a jointing material approved for porcelain pavers and outdoor use.
- For mortar‑set installations, use an exterior‑grade grout per manufacturer guidance; clean as you go to prevent haze.
- On pedestal systems, follow the pedestal/spacer manufacturer’s guidance for joint treatment and perimeter restraint.
- Remove excess jointing material from the surface before curing and final cleaning.
Step 5: Cleaning & Maintenance
- Clean routinely with water and a pH‑neutral cleaner using non‑abrasive tools.
- Avoid acidic, bleach‑based, or abrasive products that may affect surrounding materials or finishes.
- Promptly remove construction residues and grout haze following manufacturer recommendations.
- Porcelain pavers generally do not require sealing; inspect joints and borders periodically and maintain as needed.
Disclaimer
Shade and size variation can occur between production runs; verify caliber and dye lot before installation. Inspect all materials prior to install—installed materials are considered accepted. Professional installation is recommended to ensure code compliance, structural integrity, and long‑term performance.
