Intricate Bianco Veincut 12×24 Porcelain Tile Matte Rectified
Linear and refined, Intricate Bianco Veincut delivers a sophisticated vein‑cut stone look in a versatile 12×24 format. The matte surface softens glare while rectified edges support clean, consistent grout joints for modern, seamless layouts across coordinated spaces.
Crafted in durable porcelain, this tile balances style with everyday practicality. Its 12×24 size reduces grout lines, and a DCOF of 0.42 (wet) supports appropriate traction for interior floor applications. Use it to create cohesive designs on floors and walls, from kitchens and baths to living areas and feature walls.
Box planning is straightforward: 15.50 sq. ft. per box (approximately 1.94 sq. ft. per piece; 8 pieces per box). Blend tiles from multiple boxes to distribute shade and linear patterning before installation.
Features
- Material: Porcelain
- Color/Design: Bianco Veincut, vein‑cut stone look
- Finish: Matte
- Edge: Rectified for precise, tight joints
- Size: 12×24 rectangular tile
- DCOF (wet): 0.42
- Coverage: 15.50 sq. ft. per box | approx. 1.94 sq. ft. per piece | 8 pieces per box
- Low maintenance and easy to clean
Recommended Applications
- Residential interior floors
- Residential interior walls
- Backsplashes
- Shower walls
- Fireplace surrounds
- Commercial interior walls (as appropriate)
Installation Guide – Intricate Bianco Veincut 12×24 Porcelain Tile Matte Rectified
Important Advisory
Follow the tile manufacturer’s instructions, local building codes, and current ANSI A108/A118 and TCNA guidelines. Confirm substrate suitability, flatness, movement accommodation, and waterproofing/drainage where required for the intended use.
Step 1: Layout & Planning
- Verify the substrate is clean, dry, structurally sound, and flat within tolerances for 12×24 porcelain tile.
- Dry‑lay to confirm layout, centering, and pattern direction; plan cuts to avoid narrow slivers at perimeters.
- Blend tiles from multiple boxes to evenly distribute shade and linear veining.
- Use spacers appropriate for rectified tile and include movement joints per TCNA EJ171 and project conditions.
Step 2: Tile Installation
- Use a polymer‑modified thin‑set mortar approved for porcelain and the project’s substrate/environment.
- Key mortar into the substrate, then comb with an appropriate notched trowel; back‑butter tiles as needed to improve contact.
- Set tiles with a slight slide to collapse ridges, achieving required coverage (typically 80–95% based on area and exposure).
- Employ a tile leveling system when helpful to reduce lippage on larger formats.
- Allow mortar to cure per manufacturer guidance before grouting or traffic.
Step 3: Cutting
- Cut using a wet saw with a quality diamond blade rated for porcelain.
- Support tiles fully and mark cuts carefully to reduce chipping.
- Ease sharp cut edges where they will be exposed.
Step 4: Joint Filling
- Select a grout suitable for porcelain and the chosen joint width; mix and apply per manufacturer instructions.
- Pack joints completely, clean diagonally, and remove haze promptly with clean water.
- Use flexible sealant at movement joints and changes of plane; do not grout these areas.
- Protect the installation from traffic until grout has cured.
Step 5: Cleaning & Maintenance
- Clean routinely with a pH‑neutral cleaner approved for porcelain tile; avoid harsh acids or abrasives.
- Use entry mats and protective pads to minimize tracked grit and scratching.
- Follow grout manufacturer maintenance recommendations; seal cementitious grout if specified.
Disclaimer
Installation should be performed by qualified personnel. Always confirm actual materials, lot variations, and suitability for specific applications before installation. Stone Market USA is not responsible for issues arising from improper installation, handling, or site conditions.
