Happy Floors Eva Silver Pebble 12×24 Porcelain Tile Natural Rectified
Clean and versatile, the Happy Floors Eva Silver Pebble 12×24 porcelain tile blends a soft silver‑gray stone look with a natural matte surface. The 12×24 format minimizes grout lines for a smooth, modern layout, while precise rectified edges help achieve tight, consistent joints across floors and walls.
Engineered in durable 9mm (3/8 in) porcelain with a PEI 5 wear rating and a high wet DCOF (>0.59), this tile balances design flexibility with everyday performance—well‑suited to busy homes and light commercial interiors. Frost resistance expands possibilities to exterior facades in freeze–thaw climates.
Planning is straightforward: box coverage is 11.63 sq. ft. (6 pieces). Use on its own for a clean, contemporary canvas or pair with coordinating trims to complete edges and transitions.
Features
- Porcelain body for durability and low maintenance
- Color: Silver Pebble
- Finish: Natural (matte) surface
- Edge: Rectified for precise, narrow grout joints
- Size: 12×24 tile
- Thickness: 3/8 in (9mm)
- PEI 5 wear rating supports heavy residential and light commercial floors
- DCOF: >0.59 (wet) for enhanced traction
- Frost resistant for freeze–thaw exterior wall applications
- Coverage: 11.63 sq. ft. per box | 6 pieces per box
Recommended Applications
- Residential interior floors
- Residential interior walls
- Light commercial interior floors
- Commercial interior walls
- Backsplashes
- Shower walls
- Fireplace surrounds
- Exterior walls/facades (freeze–thaw)
Installation Guide – Happy Floors Eva Silver Pebble 12×24 Porcelain Tile Natural Rectified
Important Advisory
Always follow the tile manufacturer’s instructions, local building codes, and recognized industry standards (ANSI A108/A118 and TCNA guidelines). Verify substrate suitability, movement accommodation, and waterproofing/drainage where required.
Step 1: Layout & Planning
- Confirm the substrate is clean, dry, structurally sound, and flat within tolerances for large-format tile (12×24).
- Dry-lay to refine layout, balance cuts, and align grout joints with room sightlines.
- Blend tiles from multiple boxes to distribute shade and pattern variation evenly.
- Use spacers appropriate for rectified tile and include movement joints per TCNA EJ171.
Step 2: Tile Installation
- Use a polymer-modified thin-set mortar rated for porcelain and large-format tile.
- Key mortar into the substrate, then comb with an appropriate notched trowel; back-butter tiles as needed to improve coverage.
- Set tiles with a slight back-and-forth motion to collapse ridges and achieve required bond; target 80–95% coverage based on area and exposure.
- Use a tile leveling system when needed to help minimize lippage on large-format installations.
- Allow mortar to cure per manufacturer guidance before grouting or light traffic.
Step 3: Cutting
- Cut with a wet saw using a premium diamond blade suitable for porcelain.
- Mark and support tiles carefully to minimize edge chipping.
- Ease sharp cut edges where they will be exposed.
Step 4: Joint Filling
- Select a grout appropriate for porcelain and the intended joint width; follow manufacturer instructions for mixing, application, and cure times.
- Pack joints fully with a rubber float, clean diagonally, and remove haze promptly with clean water.
- Use suitable sealant at movement joints and changes of plane; do not grout these areas.
- Protect the installation from traffic until grout has cured.
Step 5: Cleaning & Maintenance
- Clean routinely with a pH-neutral cleaner approved for porcelain; avoid acids or harsh abrasives.
- Use entry mats and protective pads to minimize tracked-in grit and scratching.
- Follow grout manufacturer maintenance recommendations; seal cementitious grout if specified.
Disclaimer
Installation should be performed by qualified professionals. Verify suitability for the specific project, including site conditions and exposure, before installation. Stone Market USA is not responsible for issues arising from improper installation, handling, or site conditions.
