B-Natural Kaolin Natural Rectified Porcelain Tile 24×24
Create a clean, contemporary surface with B-Natural Kaolin Natural Rectified Porcelain Tile 24×24. Its soft kaolin color and natural finish bring a calm, versatile character to floors, walls, backsplashes, and other architectural surfaces.
Made from porcelain with a 3/8-inch thickness, rectified edges, a PEI 5 rating, and a wet DCOF greater than 0.42, this 24×24 tile is designed for suitable residential and commercial applications. Its frost-free designation may support appropriately specified freeze-resistant installations when the complete tile system and project conditions meet applicable requirements.
B-Natural Kaolin is sold by the square foot. Each 24×24 tile provides approximately 3.876667 square feet of coverage, and each box contains 11.63 square feet across three pieces.
Features
- Kaolin color with a natural finish for a soft, understated surface.
- Porcelain construction for durable performance in supported applications.
- 24×24-inch square format creates a broad, coordinated visual field.
- Rectified edges support carefully aligned grout joints and a refined installation.
- 3/8-inch thickness provides a substantial tile profile.
- PEI 5 rating supports suitable residential and commercial floor applications.
- Wet DCOF greater than 0.42 for appropriately specified wet-area applications.
- Frost-free designation may support properly specified freeze-resistant installations.
- Sold by the square foot; each box covers 11.63 square feet and contains three tiles.
Recommended Applications
- Residential interior floors
- Commercial interior floors
- Residential interior walls
- Commercial interior walls
- Kitchen backsplashes and other interior wall applications
- Appropriately specified exterior or freeze-resistant surfaces where the complete installation system meets project requirements
Installation Guide – B-Natural Kaolin Natural Rectified Porcelain Tile 24×24
Important Advisory
Review the current Happy Floors recommendations and confirm that the tile, setting materials, substrate, and planned application are compatible before beginning work. Installation should follow applicable local building codes, recognized tile-industry standards, and project-specific requirements.
Step 1: Layout & Planning
- Verify the tile size, shade, caliber, finish, edge, and quantity before installation. Review pieces from multiple boxes to understand normal variation and establish the preferred layout.
- Dry-lay representative tiles when practical. Plan the layout to balance cuts, maintain visual alignment, and coordinate the kaolin color across the installation.
- Mark reference lines so the installation remains square and aligned. Plan movement accommodation according to the substrate, room size, climate, and applicable industry guidance.
- Because the tile has rectified edges, use a consistent joint width appropriate for the installation and product tolerances rather than placing tiles edge to edge.
Step 2: Tile Installation
- Install over a clean, sound, dry, and properly prepared substrate that is flat and suitable for porcelain tile. Correct cracks, excessive variation, moisture concerns, or structural deficiencies before setting tile.
- Select a mortar or setting material rated for porcelain tile and appropriate for the specific substrate and application. Follow the setting-material manufacturer’s mixing, open-time, and application instructions.
- Apply mortar evenly and achieve the coverage required by applicable installation standards and project conditions. Periodically lift a tile to verify contact, and do not place tile over mortar that has skinned over.
- Set each tile according to the planned layout, pressing and adjusting it for proper contact, consistent joints, and a reasonably flush surface. Remove excess mortar from the joints before it hardens.
- Allow the installation to cure according to the setting-material manufacturer’s instructions before grouting or subjecting the surface to traffic.
Step 3: Cutting
- Measure and mark cuts carefully, allowing for the planned joint and movement spaces. Use a clean, appropriately rated wet saw or other professional cutting equipment suitable for porcelain tile.
- Support the tile during cutting and use suitable eye, hearing, and respiratory protection. Inspect cut edges and position cut pieces where they are least visible when the layout permits.
- Dry-fit cut pieces before setting them, and avoid using damaged or visibly defective pieces in prominent areas.
Step 4: Joint Filling
- Confirm that mortar has cured and that joints are clean, dry, and free of setting material before grouting.
- Choose a grout compatible with porcelain tile, the planned joint width, and the use conditions. Follow the grout manufacturer’s instructions for mixing, application, cleaning, and curing.
- Apply grout carefully and remove excess from the tile surface before it hardens. Use clean water and suitable tools to minimize haze, then protect the installation until the grout has cured as directed.
- Use an appropriate flexible sealant rather than rigid grout where movement joints or changes of plane are required, following the project design and recognized industry standards.
Step 5: Cleaning & Maintenance
- Remove installation residue using products approved for porcelain tile and follow the cleaner manufacturer’s directions. Test any cleaning product in an inconspicuous area first.
- For routine care, use a soft mop or cloth with a pH-neutral cleaner suitable for porcelain. Avoid abrasive tools and harsh products that could damage the natural finish.
- Clean spills and tracked dirt promptly, especially in high-use areas. Do not use maintenance procedures or sealers unless they are specifically recommended for this porcelain surface and application.
Disclaimer
Stone Market USA provides general installation information for planning purposes. Site conditions, substrate construction, climate, and use can affect installation requirements. A qualified tile professional should verify project conditions and follow the tile, mortar, grout, sealant, and cleaner manufacturers’ instructions, as well as applicable codes and recognized industry standards.
