Cardosia Sand White 12×24 Porcelain Tile Natural Rectified
Refined and versatile, the Cardosia Sand White 12×24 porcelain tile brings a soft, sand-washed white tone with a natural matte surface. Precise rectified edges support tight, consistent joints for a clean, contemporary layout across floors and walls.
Engineered in durable porcelain at 9mm (3/8 in.) thickness, this tile balances style with everyday practicality. Frost resistance expands design possibilities to exterior facades in freeze–thaw climates, while the 12×24 format helps minimize grout lines for a smooth, modern look in kitchens, baths, and living spaces.
Use it alone for minimalist continuity or mix with complementary materials to create layered, architectural detail that suits both warm and cool palettes.
Features
- Material: Porcelain
- Color: Sand White
- Finish: Natural (matte)
- Edge: Rectified for precise, narrow grout joints
- Size: 12×24 tile
- Thickness: 3/8 in. (9mm)
- PEI 3 wear rating for moderate residential floor use
- DCOF: 0.42 (wet)
- Frost resistant for freeze–thaw exterior wall applications
- Coverage: 13.56 sq. ft. per box | 7 pieces per box
Recommended Applications
- Residential interior floors
- Residential interior walls
- Backsplashes
- Shower walls
- Commercial interior walls
- Fireplace surrounds
- Exterior walls/facades (freeze–thaw)
Installation Guide – Cardosia Sand White 12×24 Porcelain Tile Natural Rectified
Important Advisory
Always follow the tile manufacturer’s instructions, local building codes, and current ANSI A108/A118 and TCNA guidelines. Confirm substrate suitability, movement accommodation, and waterproofing/drainage where required for the intended area of use.
Step 1: Layout & Planning
- Verify the substrate is clean, dry, structurally sound, and flat within industry tolerances for larger-format tiles like 12×24.
- Plan the layout by dry-laying tiles and centering the design to avoid narrow perimeter cuts.
- Blend tiles from multiple boxes to distribute shade/pattern variation evenly.
- Use spacers consistent with rectified tile and include movement joints per TCNA EJ171 and project conditions.
Step 2: Tile Installation
- Use a polymer-modified thin-set mortar approved for porcelain and, when applicable, for large-format tiles.
- Key mortar into the substrate, comb with an appropriate notched trowel, and back-butter tiles as needed to improve bond and coverage.
- Set tiles with a slight back-and-forth motion to collapse ridges; achieve coverage as required by standards and site conditions (higher in wet/exterior areas).
- Use a leveling system when helpful to minimize lippage on larger-format installations.
- Allow mortar to cure per manufacturer guidance before grouting or light traffic.
Step 3: Cutting
- Cut with a wet saw using a premium diamond blade rated for porcelain.
- Mark cuts carefully and support the tile fully to reduce chipping.
- Ease sharp cut edges where they will be exposed.
Step 4: Joint Filling
- Select a grout suitable for porcelain and the chosen joint width; follow manufacturer instructions for mixing, application, and cure.
- Pack joints fully with a rubber float, clean diagonally, and remove haze promptly with clean water.
- Use appropriate sealant at changes of plane and movement joints; do not grout these areas.
- Protect the installation from traffic until grout has cured per manufacturer guidance.
Step 5: Cleaning & Maintenance
- Clean routinely with a pH-neutral cleaner approved for porcelain tile; avoid acids and harsh abrasives.
- Use entry mats and felt pads to reduce tracked-in grit and potential surface abrasion.
- Follow grout and mortar manufacturers’ maintenance recommendations; reseal cementitious grout if advised.
Disclaimer
Installation should be performed by qualified professionals. Verify actual materials, lot-to-lot variations, and suitability for specific applications prior to installation. Stone Market USA is not responsible for issues arising from improper installation, handling, or site conditions.
