Honed Limestone Mosaic Tile 12×12

LIMESTONE MOSAIC HONED TILE INSTALLATION GUIDE

Maximize the Performance of Your Limestone Mosaic Honed Tile

Achieve a flawless and long-lasting installation by following these essential steps for preparing, installing, and finishing your Limestone Mosaic Honed Tile. Proper installation ensures durability while enhancing the stone’s natural beauty.

Step 1: Surface Preparation

A well-prepared surface is critical for a successful tile installation. Ensure the substrate is:

• Clean, dry, and free from wax, grease, soap scum, and debris.
• Structurally sound and level, with no cracks or loose sections.
• Properly waterproofed, especially in moisture-prone areas.
• Cleared of any moldings or obstructions that may interfere with tile placement.
• If necessary, apply a self-leveling compound to create an even surface before installation.

Step 2: Layout Planning

• Measure the installation area and mark the center points of all four walls.
• Snap chalk lines between opposite walls to establish a precise grid for tile alignment.
• Dry-lay a row of tiles along the center lines in both directions to ensure even distribution and a balanced pattern.
• Adjust the center line if edge cuts are too small.
• Use tile spacers to maintain uniform grout joints.

Step 3: Selecting & Applying Adhesive

Choosing the right adhesive is crucial for a strong bond. We recommend using a high-quality white thin-set mortar, such as:

• Mapei
• Laticrete
• Ardex

Application:

1. Mix only the amount of mortar that can be used within 30 minutes.
2. Apply a 1/4-inch adhesive layer using the flat side of a notched trowel.
3. Comb the adhesive with the notched side of the trowel at a 45-degree angle to create even ridges.
4. Work in small sections (2’ x 3’) to prevent the mortar from drying before tile placement.
5. For moisture-sensitive stones, use a setting material recommended by the manufacturer.

Step 4: Cutting & Fitting Tiles

1. Mark tiles accurately using a pencil or marker.
2. Use a tile cutter for straight cuts and a wet saw with a diamond blade for precise edges.
3. Smooth, rough edges with a rubbing stone.
4. Use a tile nipper for curved cuts to chip away excess material gradually.
5. Dry-fit all tiles before applying mortar to ensure a snug fit.

Step 5: Setting the Tiles

1. Start laying tiles from the center of the room, working outward within each grid.
2. Place tiles with a slight twisting motion to secure a firm bond.
3. Avoid sliding tiles into position to prevent mortar displacement.
4. Use spacers to maintain consistent grout joints.
5. Tap each tile gently with a rubber mallet to ensure even placement.
6. Wipe off excess mortar with a damp sponge.
7. Allow the adhesive to cure for at least 24 hours before grouting.

Step 6: Grouting & Finishing

1. Remove tile spacers before applying grout.
2. Use a high-quality, non-sanded grout for limestone mosaics.
3. Spread the grout diagonally across the tiles using a rubber float, ensuring joints are filled.
4. Remove excess grout immediately using the float’s edge.
5. Wait 15–20 minutes, then wipe off the grout haze with a damp sponge.
6. Allow grout to cure for 72 hours before exposing the surface to heavy use.
7. Apply a penetrating sealer after the fully cured grout to protect the stone from stains and moisture.

Maintenance Tips

• Use pH-neutral stone cleaners to maintain the natural look of limestone tiles.
• Avoid acidic or harsh cleaning agents that may damage the surface.
• Reseal the stone regularly to maintain its durability and appearance.
• Place felt pads under furniture to prevent scratches.

Important Notice:

Stonemarket USA is not responsible for improper installations. We strongly recommend hiring a professional tile installer and using premium-grade materials for the best results.

For any questions, contact Stonemarket USA Customer Support.

By following these expert installation guidelines, you’ll enjoy the timeless beauty and durability of your Limestone Mosaic Honed Tile for years to come.